What are Blu-ray and DVD region codes, country codes, multi-region or zone locks? Read DVD Player region codes and Blu-ray region codes.
| DVD Player | Hacks | Updated | Add |
| Sony RDR-HX950 | 4 user region code comments |
August 23, 2009 | Post region code/hack comment |
 Region code posted by Alar, April 04 2008: | |||
Uses pc program for infrared device to send codes to player. Read http://www.selen.org/sonydvd.html Needs bootable usb, how2 http://www.bay-wolf.com/usbmemstick.htm I prefere bootable cd made with magiciso. | |||
| Region code hack posted by monkeybeast, October 06 2008: | |||
As per the RDR-HX750 hack, but I used the All for One 3440, and it went exactly as posted. One note, in the hack it says repeat steps 2 and 3. You need to repeat steps 1, 2 and 3. Am a happy man because now I can buy much cheaper US DVD's. | |||
| Region code hack posted by trytagger, December 17 2008: | |||
I had my Sony RDR-HX950 hacked using this method. First your psp "phat" have to be install with IR Shell. Copy this RDF file into the ircode folder. * Switch on recorder and point its own remote at it * System Setup -> Initial Setup -> Options -> Command-Mode * Select DVD1 * Switch the recorder to standby. * Run IRshell, IR Remote View and select Sony Region. * Press 'Cross', 'Circle', 'Triangle', 'Square', 'Up'. * The recorder turn on with welcome message. * Wait until you can access the recorder then continue. * Press 'Cross', 'Circle', 'Triangle', 'Square', 'Up'. * The recorder display will say "timer ok". And you have hack it! To check. * Switch on the recorder * System Setup -> Initial Setup -> Options -> Audio Out -> Dolby Digital Output -> Dolby Digital -> PCM. * Press 'Angle" key. * You will see Region 14 rather your original region. Happy Region-free day!!!!!!!!! Tested: RDR-HX950 RDR-HXD770 | |||
| Region code hack posted by stvngo, August 23 2009: | |||
I used the method described on the top by Alar on my RDR HX950 with success, but it took me a long time to get it right. My experience with it may save someone else some time. Once I got the my PC set up to run the IRDA exe and was sure that it actually sent a signal that the player actually recieved (took a while) it was difficult to get it to work properly. All the guides on the method I read sead to do it slower, pausing between buttons etc. As a final resort to get it to work I did the opposite. And finally it worked. If everything is set up and working properly the following is how it should work on the HX950: 1) The player should be set to: Command-set DVD1 for remote 2) The player should be turned off (standby mode) 3) Using the programs and code files from www.selen.org, select and press (as instructed) 1 (enter) 2 (enter) 3 (enter) 4 (enter) 5 (enter) 4) The player will now start up as though turned on by the regular remote, displaying "WELCOME" in the display. 5) HERE'S THE IMPORTANT PART. While it still displays the "WELCOME" message, you have to repeat step 3. You will need to do this very quickly! 6) If you are quick enough and successful, the display will now show "TIMER OK" and power down. 7) If it just displays "POWER OFF" then start over again, until you get it. Patience and speed are key here! Good luck :) | |||
| 1 DVD Hack hits, Showing 1 to 1 DVD Hacks |
New hacks = New region code/hack comments since your last visit. Visit our sponsors! Try DVDFab and backup Blu-rays!